Serving Waukegan, Zion & Lake County
GE and GE Profile refrigerators, laundry, dishwashers, ranges and microwaves repaired across Lake County.
GE Repair
From refrigerators and dishwashers to ranges and over-the-range microwaves, we repair GE and GE Profile models in Waukegan, Zion, Beach Park and the surrounding towns.
Typical GE repairs include refrigerators that stop cooling, dryers with drum or belt problems and dishwashers that won’t drain. We find the cause, explain it plainly and quote the repair before we start.
Also covers: GE Profile, GE Café, Hotpoint
IyJ Repairs is an independent repair company and is not affiliated with GE.
Error Codes
GE ranges and wall ovens use F-codes. GE laundry and refrigerators mostly signal problems through behavior or blinking lights rather than codes, so tell us what the appliance does when you call.
| Code | Appliance | Meaning | Usual fix |
|---|---|---|---|
| F0 / F1 | Oven | Control board or keypad fault | Control board; sometimes the keypad |
| F2 | Oven | Oven overtemperature | Temperature sensor or control relay |
| F3 | Oven | Temperature sensor shorted | Temperature sensor |
| F4 | Oven | Temperature sensor open | Temperature sensor or its wiring |
| F7 | Oven | Stuck key / keypad fault | Keypad or control board |
| F9 | Oven | Door latch fault (self-clean) | Door lock motor or switch |
| Blinking lights | Dishwasher | Control lock or a fault flash pattern | Clear the control lock; otherwise count the flashes and tell us |
By Appliance
What tends to go wrong on each GE appliance line, and what the fix normally involves.
GE dryers are known for drum-support wear: the belt, idler pulley, drum bearing and the felt slides and glides at the front of the drum. A squeal is the idler or bearing, a thump is a flat roller or worn slide, and a drum that won’t turn is the belt.
Usual fix: Belt, idler, bearing and slide/glide kit, replaced together.
GE and GE Profile refrigerators warm up when the evaporator ices over (defrost heater, thermostat or main board) or when a fan fails. Many models use a main control board that also drives the fans and damper, so a dead board can show up as several symptoms at once.
Usual fix: Defrost heater or thermostat, fan motor, or main control board.
GE dishwashers drain through a check valve and pump that clog with food and glass. A new install that never drained usually has the disposal knockout plug still in place.
Usual fix: Clear the check valve and pump, replace the drain pump, or remove the knockout plug.
F2, F3 and F4 are the temperature sensor and control; F7 is a stuck key; F9 is the self-clean door latch. Without a code, a cold electric oven is the bake element and a cold gas oven is the igniter.
Usual fix: Temperature sensor, control board, bake element or igniter, depending on the code.
GE top-loaders leak from the tub seal or inlet hoses and stop spinning when the lid switch, belt or clutch wears. GE front-loaders are newer and fewer, and usually report drain or door problems on the display.
Usual fix: Lid switch, belt, clutch, hoses or tub seal.
IyJ Repairs is an independent, family-owned repair company. We are not a GE authorized service center; Midea is the brand we are factory-certified for.
What Neighbors Are Saying
“I have used Israels service time and time again. He is always on time and knows exactly what he is doing and his rates are reasonable. I recommend his service anyday. Satisfied customer ”
“He Fixed The issue in less than an Hour! & very affordable!!! Definitely will use in the future & refer ”
“Israel is a great person to call to get your appliances repaired. He is very knowledgeable & personable. He fixed my washing machine & did a great job for a good price. I would highly recommend him!”
Common Questions
What GE owners ask us most.
Ready to Get Started?
Book online in under two minutes — or call us directly, we pick up.